Get Offer

 

 

We have uncovered this great article relating to Tools You Need to Install a New Bathtub directly below on the internet and believe it made good sense to share it with you on this page.

Mounting a bathtub isn't precisely brain surgery, but it does call for solid plumbing, carpentry, and often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately hard task. If the old tub is readily available, the task can relocate speedily; if you have to open a wall to get rid of the old tub and position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to vacate the old tub and embeded in the new one. See to it you have actually certified yourself for the task and also are comfortable attempting it. Rather than employing a contractor to take over a halfway-completed project, it is much better to think about employing one before you begin. Chances are you may need a professional plumber to make tube links.
This article will certainly help you set up a brand-new bathtub in your shower room if you have actually currently gotten a brand-new bathtub as well as do not require to alter the setup of your previous water system pipelines.
Your devices and also product list need to consist of the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you require to replace old taps with new ones as a part of your installment, then the first thing you ought to do is detach the supply of water. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be fairly problematic due to the limited accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a fabric ready for the continuing to be water that will come from the pipes. When the supply pipes have been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming throughout this process. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.

 

 

Suitable New Touches

If the tails of the new taps are plastic, after that you will require a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in location between the faucet as well as the sink. Secure the tap in place with the supplier supplied backnut. Once the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be linked to the tap finishes initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Installing the Bathtub

Utilizing the two wooden boards under its feet, position the bathtub in the called for position. The wood boards are practical in uniformly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 little factors.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by examining the level as well as adjusting the feet on the bathtub up until the spirit level checks out level.
To mount faucets, fit the bottom of the furthest adaptable faucet connector to the proper supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Switch on the supply of water as well as check all joints and brand-new pipework for leakages and also tighten them if necessary. Fill up the bathtub and also examine the overflow electrical outlet and the normal outlet for leaks.
Lastly, deal with the bath paneling as defined in the maker's user's manual. Tiling as well as sealing around the bath tub ought to wait till the bathtub has been utilized a minimum of once as this will settle it into its final position.

 

 

Preparing for the Installment

Firstly, the sustaining frame supplied with the bathroom ought to be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to ensure that if the tap comes with a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop stress on the bathtub.
Fit the adaptable tap ports to the bottom of both faucets making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be suited its last placement.

 

 

Tiling Around the Bath tub

In the area where the bath satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall in between the bath and also the tiling, resulting in issues with wetness and possible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your components as well as installations. They are offered in tubes as well as cartridges, and are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to always load the bathtub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can break fairly early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also quickly offered on the market. It is recommended to fit the tiles making use of waterproof or waterproof adhesive as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We are very involved in How to Install a Bathtub and I really hope you enjoyed our blog entry. Liked our review? Please share it. Let another person find it. I value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Booking Page